7/5/2023 0 Comments Psp100 receipt printersetup![]() ![]() The first thing to do is turn off the printer, wait five seconds, and turn it back on. The IP address under "Current IP Parameters Status" displays zeroes.Take a look at the printed paper to see if any of the following issues match the text displayed: The printer tries to connect to the internet and then continues to print off more diagnostic information. Let the printer print off the firmware information and then let go of the feed button. While still holding the FEED button, turn the printer back on. To debug your printer, turn your printer off and press and hold the FEED button. This restarts your printer and usually fixes any issue on the printer's end. Your printer requires an internet signal to run properly.Ĭheck to see that your printer appears on the Hardware settings screen on the Shopify POS app. Steps:Ĭheck to see that your network cable is connected to your wireless router.Ĭheck to see that you are connected to the internet. Your printer might not be working for several reasons. If your TSP143IIILAN printer stops working Test the connection to the cash drawer (if applicable).Set it as the default printer (optional).The receipt printer must be connected to the same network as your iPad.Īfter connecting your printer, don't forget to: This makes the printer discoverable in the Shopify POS app. Optional: Connect the receipt printer to a supported cash drawer using the cash drawer cable.Ĭonnect the receipt printer to the Ethernet port on your router. Insert a roll of thermal printing paper into the printer. Turn the receipt printer on using the power switch. Plug the receipt printer to a power source. Be sure to use the correct cables when you connect the printer. If you buy it elsewhere, then you need to buy the Ethernet cable. If you bought your cash drawer separately, your supplier should be able to sell you a cable.Įthernet cable (for connecting to the router)Īn Ethernet cable approximately 1 m in length is included when you buy this printer from Shopify. Cable typeĪ cable for the cash drawer is included in the retail custom kit from Shopify. To use this printer, you must have a network set up in your location and a router that you can connect your printer to using an Ethernet cable.īefore you get started, make sure you have the cables that you need. The TSP143IIILAN receipt printer connects to your network using an Ethernet cable. the length does not exceed 230 feet (70m).įor an explanation of how to load the receipt printer, see the guide in the manufacturer's hardware manual.Buying printer paperĪny thermal paper rolls work with this printer if: The Star Micronics TSP143IIILAN receipt printer is available from the Shopify Hardware Store in supported countries. Where to buy the Star Micronics TSP143IIILAN receipt printer a compatible iPad that is running iOS 13 or higher, an iPhone that is running iOS 13 or higher, or a compatible Android device that is running version 7.0 (Nougat) or higher.To use this hardware with your Shopify store, you need to meet the following requirements: Limitations when using the Star Micronics TSP100III LAN receipt printer.If your printer is a long distance from your router.If your TSP143IIILAN printer stops working.Where to buy the Star Micronics TSP143IIILAN receipt printer.If a test receipt prints, click Save and you are done. ![]() Select Direct, Star TSP100 and select the COM from the PORT drop down and click Test. Open the Phorest Software and go to Manager>Settings>Point of Sale> Device Select Add Port and select the Com you wish to use.Ĭlick Apply Changes and click Check Health. When the configuration utility opens, select Serial Ports When the utility opens, select ESC/POS Mode Open the Configuration Utility by clicking the windows button (bottom left) and type in Configuration Utility. Open the Phorest software and go to Manager>Settings>Terminal Settings and select Direct, Star TSP100 and the com you set up previously and click Test, click Save and you are done!Įxtract the files to your desktop, open the folder, and double-click on the file highlighted below. Open the configuration Utility, select Serial Ports and add a COM. Quick Version: Download the drivers, extract them, and run the auto-installer. Note: If you're installing on an Apple Mac computer, click here. The following instructions will show you how to set up a Star TSP100 receipt printer with Phorest Cloud on a Windows computer. ![]()
0 Comments
Leave a Reply. |